The main difference between the two types of boards is their size, with longboards being wider and longer than skateboards. As a result, longboard trucks tend to be larger and have a different geometry than skateboard trucks.
However, this does not mean that they are incompatible. It is possible to put longboard trucks on a skateboard. You will need tools including a power drill, wrench, or tool for your board and new hardware depending on what you want the final result of it all looks like-
whether it’s stylishly vintage looking with red-tinted riser pads which allows them grip when riding off-road but knows how much pressure should be applied so there isn’t excessive wear from doing tricks too fast! In fact, many skaters enjoy the stability and speed that longboard trucks provide.
If you’re looking to experiment with different setups, you may find that longboard trucks are worth a try. Just be prepared for a new skating experience.
What Do You Need To Put Longboard Trucks On A Skateboard?
You might need riser pads (and they are very much encouraged) if you attempt to turn your skateboard into a cruiser.
To turn your longboard trucks into skateboards, you are going to need:
- Longboard trucks (axle width should be no wider than 8.0″)
- Riser pads
- Skateboard wheels (70mm to 80mm wheels recommended)
The only thing you need to be aware of is the axle width of the longboard trucks. Most standard skateboard trucks have an axle width of 7.75″, while most longboard trucks have an axle width of 8.0″. This means that you might need to get new hardware to fit the longboard trucks onto your skateboard.
Additionally, you will also need riser pads to avoid wheel bite when turning. Other than that, you should be good to go! Just put on your new longboard trucks and enjoy the ride.
Things To Consider Before Putting Longboard Trucks On Skateboard
Although it is possible to put longboard trucks on a skateboard, there are a few things to consider before doing so.
For one, the axle width of longboard trucks is usually wider than that of standard skateboard trucks. This means that you might need to get new hardware to fit the longboard trucks onto your skateboard. Additionally, you will also need riser pads to avoid wheel bite when turning.
Next, consider the bushings of your skateboard. Bushings are the small, plastic pieces that sit between the trucks and the wheels. Softer bushings will make your ride smoother, while harder bushings will make it more responsive. Keep this in mind when choosing longboard trucks for your skateboard.
Another thing to consider is the weight of the longboard trucks. Longboard trucks are typically heavier than skateboard trucks, which can affect the performance of your skateboard. If you are looking to use your skateboard for tricks and flips, then you might want to stick with skateboard trucks.
Just be sure to keep the above things in mind before making the switch!
Features of longboard trucks
Longboard trucks are made up of several main components:
The hanger is the metal part of the truck that holds the wheels. It is connected to the baseplate with two kingpins.
The baseplate is a flat, circular piece of metal that attaches to the skateboard deck. It has holes for mounting the trucks and attaching the hardware.
The kingpins are the large bolts that connect the hanger to the baseplate. They are responsible for the turning action of the truck.
The bushings are what allow your board to turn and pivot smoothly. They’re made of a soft urethane, which means they will never wear out or get scratched by metal parts on the kingpin as you ride it around town!
The axle is the metal rod that runs through the center of the wheel. The width of the axle will determine the turning radius of the truck.
The wheels are made of hard plastic and come in a variety of sizes, shapes, and colors. The size of the wheel will affect the speed and smoothness of your ride.
The bearings are the small, metal pieces that sit between the axle and the wheel. They allow the wheel to spin freely.
Now that you know the different parts of longboard trucks, let’s take a look at how to put them on your skateboard.
How To Put Longboard Trucks On A Skateboard
Mounting longboard trucks is a simple process, but there are a few things you need to keep in mind. First, make sure that the truck mount holes line up with the holes on your deck. If they don’t, you’ll need to drill new holes.
Second, if you had to fill in any old holes, be sure to replace the grip tape before mounting the trucks.
One of the most important things to keep in mind when setting up a longboard or cruiser is to make sure the trucks are facing the right way. The kingpin on longboard trucks should face outwards, as opposed to facing in like on a skateboard.
This may seem counterintuitive at first, but it’s important to remember if you want to avoid any accidents while cruising around on your new board. Once the trucks are mounted to the board, you can then add your choice of cruiser or longboard wheels.
If you’re a skateboarder, you know that one of the most annoying things is getting a wheel bite. Wheel bite happens when your wheels catch on the edge of your skateboard, causing you to bail. Not only is it annoying, but it can also be dangerous. So what can you do to prevent wheel bite?
One option is to add riser pads to your skateboard. Riser pads sit between your deck and your trucks, and they raise your wheels up slightly. This helps to prevent them from catching on the edge of the deck.
Another option is to sand down the area above the wheels. This will create a beveled edge that won’t be as likely to catch your wheels.
Ultimately, it’s up to you to decide what works best for you. But if you’re having problems with wheel bite, these are two options that you can try.
What’s The Difference Between Longboard Trucks And Skateboard Trucks?
The main difference between longboard trucks and skateboard trucks is the width of the axle. Longboard trucks have an axle width of 8.0″, while skateboard trucks have an axle width of 7.6 inches.
Additionally, longboard trucks are typically heavier than skateboard trucks, which can affect the performance of your skateboard. Finally, the wider turning radius of longboard trucks can make it difficult to do tricks.
Pros of Putting Longboard Trucks On Your Skateboard
It’s easier to turn, thanks to the wider turning radius.
Can handle rougher terrain, such as cracked sidewalks and pebbled roads.
Smooth ride, thanks to the larger wheels.
So there you have it! These are just some of the benefits of using longboard trucks on your skateboard. If you’re looking for a smoother ride and an easier time commuting, then longboard trucks are definitely the way to go.
The Cons of Putting Longboard Trucks On Your Skateboard
Although there are many benefits to using longboard trucks on your skateboard, there are also a few drawbacks to consider:
The wider turning radius can make it difficult to do tricks.
Longboard trucks are heavier than skateboard trucks, which can affect the performance of your skateboard.
Traditional vs. Reverse Kingpin
The traditional kingpin truck is the most common type of longboard truck. It is designed for speed and stability, making it a great choice for cruising and commuting.
The reverse kingpin truck is less common, but it offers a few benefits over the traditional truck. It is more maneuverable, making it easier to do tricks. Additionally, the reverse kingpin truck is less likely to speed wobble, making it a safer choice for high-speed downhill racing.
The width of the axle will determine the turning radius of the truck. A wider axle will provide more stability, while a narrower axle will be more maneuverable.
The hanger is the metal part of the truck that holds the wheels. It is available in a variety of sizes, from narrow to wide. The size of the hanger will affect the stability and turning radius of the truck.
Is longboarding harder than skateboarding?
No, longboarding is not harder than skateboarding. In fact, many people find longboarding easier because it requires less balance and coordination than skateboarding. Longboards are also wider and more stable than skateboards, making them easier to ride.
However, longboarding is not without its challenges. Beginners may find carving and downhill racing difficult, but with practice, anyone can learn to master these skills. So no, longboarding is not necessarily harder than skateboarding – it just requires a different set of skills.
Can I use any trucks on a skateboard?
Mid-sized trucks are the most popular choice for a skateboard, and they offer good stability when doing flip tricks or other moves. Low Truck – designed to work with small wheel sizes (50mm+), these sturdy pieces of hardware help you keep your board under control during risky endeavors like jumps over obstacles in front of us!
We recommend using 53 mm wheels on lower-speed surfaces such as asphalt so that there’s less risk associated w/ corrections.
Can you put Longboard trucks on a cruiser board?
Some cruisers come with drilled holes that allow you to attach longboard trucks, while others don’t. Ultimately, it depends on the kind of cruiser board you have and whether or not it’s compatible with longboard trucks. If you’re unsure, it’s always best to consult with a professional skate shop or the manufacturer of your board.
In conclusion, it seems that longboard trucks can fit on skateboards- with a little bit of modification. However, you’ll also need the right parts like boards with risers pads and new hardware-Skateboarders looking to try out this new trend may want to take into account the width and height of their board before purchasing new trucks, to ensure compatibility. Happy riding!