Have you ever noticed how many people skateboard without properly maintaining their wheels? It may seem like an oversight, but it could cause major problems if not taken care of. The only thing between us and the ground is our skateboards tires; they should be inspected regularly.
Having uneven skateboard wheels can cause a lot of problems, including decreased performance and even potential injuries. Luckily, there are a few simple tricks that you can use to fix the problem. In this blog post, we’ll discuss what causes uneven skateboard wheels and how to fix them using easy ways. Stay safe out there on your board!
Why Are My Skateboard Wheels Uneven? Reasons and their solutions
1. Axle Nut Problems:
If your wheels are sitting at an angle, it’s likely that the axle nuts are loose. These small metal nuts keep your wheels attached to the trucks, so if they’re not tight, the wheels will be able to move around. To fix this, simply tighten the axle nuts until they’re snug. You may need a skate tool to do this, as some axle nuts can be very tight.
2. Wheel Bite:
Another possible reason for uneven wheels is wheel bite. This occurs when the wheels rub against the deck of the skateboard, and it can cause the wheels to become misshapen.
To prevent wheel bite, make sure that your trucks are adjusted properly. The kingpin (the large bolt in the center of the truck) should be tightened or loosened until the trucks sit at a level that’s between flush and 1/8″ higher than the deck. This will give you enough clearance to avoid wheel bite without making your ride too unstable.
3. Uneven Surfaces:
If you’re riding on uneven pavement or surfaces, it’s possible for one wheel to hit a bump or crack that throws it off balance. This can cause your skateboard to veer to one side, and it can also damage your wheels. To avoid this, try to stick to smooth surfaces whenever possible. If you do find yourself riding on rougher terrain, go slowly and be careful of any potential hazards.
4. Bad Bushings:
If your skateboard wheels are uneven, it may be due to bad bushings. Bushings are the soft, rubbery rings that surround the axles of your skateboard trucks. Over time, they can become hard and brittle, causing your wheels to become misaligned. Inspect your bushings regularly for signs of wear and tear, and replace them as needed.
5. Worn-Out Bearings:
Another common cause of uneven skateboard wheels is worn-out bearings. Bearings are the small metal circles that attach to the center of each wheel. They allow the wheels to spin freely around the axles.
Over time, bearings can become rusty and damaged, causing the wheels to spin inconsistently. If your bearings are worn out, you’ll need to replace them with new ones.
6. Incorrect Wheel Alignment:
The other reason why your skateboard wheels may be uneven is incorrect wheel alignment. This occurs when the wheels are not properly secured to the axle of the truck. As a result, they can move around and become misaligned.
To fix this problem, simply loosen the bolts on your trucks and realign the wheels. Once they’re in place, tighten the bolts back down. With these tips, you should be able to fix any issue you’re having with uneven skateboard wheels.
7. Skateboard Trucks Squeak:
If your skateboard trucks are squeaking, it’s likely that the wheels are uneven. The wheels may be rubbing against the trucks, causing the squeaking noise.
To fix this, you’ll need to adjust the trucks so that they’re even with the wheels. You can do this by loosening the bolts that hold the trucks in place and then moving them until they’re level with the wheels. Once you’ve done this, tighten the bolts back up and your problem should be solved.
A Little Guidance on How to Fix Uneven Skateboard Wheels
Over time, it’s not uncommon for skateboard wheels to become uneven. This can happen for a number of reasons, including regular wear and tear, incorrect installation, or impact damage. Fortunately, there are a few simple steps you can follow to fix uneven skateboard wheels.
First, check the wheel nuts to make sure they’re tightened properly. Next, inspect the wheels for any dents or gouges that might be causing them to sit unevenly. If everything looks good so far, it’s time to spin the wheels and check for any wobble. If the problem still persists, it’s likely that the axle is bent and will need to be replaced.
With a little patience and some basic knowledge, fixing uneven skateboard wheels is a relatively easy task.
Why is my skateboard not going straight?
If you’re having difficulty keeping your skateboard going in a straight line, there are several possible causes. One reason might be that the board is not properly balanced. When standing on the board, you should be able to balance evenly on both feet.
If the board is tilted to one side or the other, it will tend to veer off in that direction. Another possibility is that the wheels are not inflated evenly. Check to see if all four wheels have similar amounts of air pressure. If one wheel is significantly under-inflated, it will cause the board to pull to that side.
Finally, make sure that the trucks (the metal axles that attach the wheels to the board) are tightened properly. Loose trucks can cause the board to wobble, making it difficult to control. By troubleshooting these potential problems, you should be able to get your skateboard back on track.
How do I stop wheel bite?
Wheel bite is a common problem for skateboarders. It occurs when the wheels of the skateboard come in contact with the ground, causing the board to stop abruptly or even sending the rider flying.
There are a few simple ways to prevent wheel bite. First, make sure that you are using wheels that are large enough for your skateboard. This will help to ensure that the wheels have enough clearance and are less likely to come into contact with the ground.
Second, make sure that you tighten your trucks by hand. This will help to create a tighter grip on the wheels and will reduce the likelihood of wheel bite. By following these simple steps, you can avoid wheel bite and enjoy a better skating experience.
Is it better to skate loose or tight?
Tight trucks are faster because they provide stability at higher speeds, which reduces the likelihood of catching that dreaded speed wobble. If you’re considering riding down hill or if a vert ramp session awaits your skillful skills then consider tightening up those straps on our end for safety’s sake.
What causes wheel misalignment?
The three main causes of wheel misalignment are sudden jarring or heavy impacts, worn parts, and improper installation. Sudden impacts can cause the suspension components to shift, resulting in misaligned wheels.
Worn parts can also cause misalignment, as they may no longer be able to support the weight of the vehicle properly. Improper installation can also lead to wheel misalignment, as the wheels may not be mounted properly on the axle.
If you suspect that your wheels are misaligned, it is important to have them inspected by a qualified mechanic to ensure that they are safe to drive on.
That’s all for today! We hope you found this article helpful. If you have any questions or want to share your tips and tricks on how you fix uneven skateboard wheels, let us know in the comments section below. Happy skating.